| Grandstream IP Phones with Tpad |
| |
|
The following instructions detail how to configure the Grandstream Budgetone VoIP IP phones with Tpad. The configuration guide is applicable to other IP Phones in the Grandstream range. |
| |
| Configuration through the Web Browser |
|
The Grandstream series IP phone has an embedded Web server that can be used to configure the phone. It has embedded HTML pages that allow a user to configure the IP phone through a Web browser such as Microsoft’s IE or Mozilla’s Firefox. |
| |
| Access the Web Configuration Menu |
The Grandstream IP Phone Web Configuration Pages can be accessed by inputting the phones IP into the browser’s URL address field like:
http://192.168.002.001 |
| |
| There are two ways to retrieve this IP address from the phone: |
- When the phone is off-hook or in speakerphone mode, simply press MENU button. (This is
most common way to get the IP address of the phone)
- When the phone is on-hook, press MENU button and then the browsing arrow keys to “[2] IP Addr”, press MENU again.
|
| |
| NOTE: |
To type IP address into browser to bring up the configuration pages, please strip out the
leading “0. e.g.: if the IP address is: 192.168.002.001, please type in: 192.168.2.1. |
| |
| Once the correct IP address of the phone is input into browser and “Enter” key pressed, the web log in page will come up like following: |
| |
|
| |
| The password is case sensitive. The factory default password for Administrator is “admin”. |
| |
| Configuration Menus |
After inputting the password into the login screen, the embedded Web server of the IP phone will respond with the Configuration Page screens, which are explained in detail below. |
|
| |
| Status Page: |
This page is just for information.
|
| Basic Settings: Tpad settings are in RED TEXT |
|
| |
| End user Password |
This contains the password for end user to access the Web Configuration Menu. This field is case sensitive and maximum length is 25 characters. The default end user password is “123”. For Administrator the default password is “admin”
|
| IP Address |
There are 2 modes under which the IP phone can operate:
If DHCP mode is enabled, then all the field values for the Static IP mode are not used (even though they are still saved in the Flash memory) and the IP phone will acquire its IP address from the first DHCP server it discovers on the LAN it attaches to.
If Static IP mode is selected, the IP address, Subnet Mask, Default Router IP address, DNS Server 1 (mandatory), DNS Server 2 (optional) fields need to be configured. These fields are set to zero by default.
DHCP mode is recommended. |
| Time zone |
Displayed date/time will be adjusted according to the specified time zone. |
| Daylight savings time |
Default NO. If set to Yes, then the displayed time will be 1 hour ahead of normal time. |
| Date displayformat |
This parameter controls the date display format. |
|
| |
| Advanced Settings: |
The Tpad settings are in RED TEXT |
|
|
| |
|
| |
|
| |
|
| |
| Admin Password |
Administrator password. Leave default |
| SIP Server |
Enter sip.tpad.com |
| Outbound Proxy |
Enter sip.tpad.com |
| SIP User ID |
Enter your TPAD phone number e.g. 1123444 |
| Authentication ID |
Enter your TPAD phone number e.g. 1123444 |
| Authenticate Password |
Enter your TPAD password |
| Preferred Vocoder |
The BudgeTone IP phone supports up to 8 different codec types including
Vocoder G711-ulaw (PCMU), G711-alaw (PCMA), G723, G729A, G726-32 (ADPCM),
G722, G728 and iLBC.
Leave as Default. |
| G723 Rate: |
Encoding rate for G723 codec. Leave default, 6.3kbps rate is set. |
| iLBC frame size |
iLBC packet frame size. Leave Default is 20ms. |
| iLBC payload type |
Payload type for iLBC. Leave Default value is 97. |
| Silence Suppression |
This controls the silence suppression/VAD feature of G723 and G729. If set to “Yes”, when a silence is detected, small quantity of VAD packets (instead of
audio packets) will be sent during the period of no talking. Set to “No”, this feature is disabled. |
| Voice Frames per |
Leave as Default |
| Layer 3 QoS |
Default value is 48. |
| Layer 2 QoS |
Default setting is blank or “0” |
| Use DNS SRV |
Default is No.
If set to Yes, the phone will use DNS SRV configured to lookup for the server |
| Use ID is phone number |
If “Yes” is set, a “user=phone” parameter will be attached to the “From” header in SIP request, which will be processed by supported SIP proxy.
Default is No. |
| SIP registration |
This parameter controls whether the BudgeTone phone needs to send
REGISTER messages to the proxy server.
The default setting is “Yes”. |
| Unregister On Reboot |
Default is No. |
| Register Expiration |
The default interval is 3600 seconds (or 1 hour). |
| Early Dial |
Default setting is No. |
Allow outgoing
call without Registration |
Default is No. |
| Dial Plan Prefix |
Sets the prefix added to each dialed number. If configured, the prefix will be
added to EVERY number input. Default is none. |
| No key Entry Timeout |
Default is 4 seconds.
User can short or extend that depends on digits dialed habit |
Use # as Dial Key |
Default is NO. |
| Local SIP port |
The default value is 5060. |
| Local RTP port |
The default value is 5004. |
| Use Random port |
Default is No. If set to Yes, the device will pick randomly generated SIP and RTP ports. This is usually necessary and useful when multiple IP Phones are behind the same full cone NAT router. |
| NAT Traversal |
Default is NO.
It should be set to YES if the device is behind NAT router. |
Keep alive interval |
Default is 20 seconds. |
| Use NAT IP |
Default is blank. |
| Proxy-Require |
Default is blank. |
| Voice Mail User ID |
Default is blank. |
| Subscribe for MWI |
Default is No. |
| Auto Answer |
Default is No. |
Offhook Auto-Dial |
Default is blank. |
Enable call features |
Default is Yes. |
Disable Call Waiting |
Default is No. |
| Send DTMF |
Set as RTP (RFC2833) |
DTMF Payload Type |
Default is 101 |
Send Flash Event |
Default is NO. |
Onhook Threshold |
Default is 800ms. |
| NTP server |
Leave as Default. |
Default Ring Tone |
Default set as “system ring tone” |
| Send Anonymous |
Default is NO. |
Anonymous Method |
Set to “Use From Header”. |
| Time to ring |
Default is 60 seconds |
| Special Feature |
Default is Standard. |
| Syslog Server |
Default is None. |
|
| |
| Click UPDATE at the bottom of the configuration page then click to view your changes and then click the REBOOT on the phone menu screen. Make sure you click UPDATE before clicking REBOOT to make sure your changes are implemented correctly. |
